SKU: 79643267582

7440 360 Degree 18 LED Bulb in Amber

Sale price$26.95 Regular price$29.95
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 13 - Jul 18

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

7440 360 Degree 18 LED Bulb in AmberRECON's New LED Bulbs Feature extremely low power consumption, have built in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours. LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the

RECON's New LED Bulbs Feature extremely low power consumption, have built-in current limiting resistors, generate practically no heat, and boast a longer life expectancy than any other automotive LED bulb currently available. RECON LED bulbs have an average life expectancy of up to 80,000 hours.

LED bulbs may cause some newer vehicles to indicate a bulb is burnt out (because of their low power consumption). Some cars indicate this by increasing the flash rate of the turn signals, some turn on a bad bulb indicator. This can be remedied with our Load Resistors wired across the turn signal bulbs to simulate a filament bulb load.
This 6 Ohm, 50 Watt resistors can be connected across the turn signal bulbs to simulate the load of a regular filament bulb (2 Amp load). This will solve LED related turn signal problems such as hyper flashing or burnt out bulb indications. This LED Load Resistor can be use with most signal or brake light which uses SINGLE or DUAL FILAMENT LED light bulbs, like the 7443, 1157, 3157, 4157, 1156, 7440, 3156 etc.
CONNECTION INSTRUCTIONS:
Using included splice taps, connect one wire to ground and the other wire to the turn/brake hot wire. Splice taps allow for installation without cutting your turn signal wires.
Automotive LED Light Bulb Load Resistor Features:
-- Solve LED related turn signal problems such as hyper flashing or burnt out bulb indications.
-- Compact design for easy installation.
-- 6 Ohm 50 Watt resistors can be use will most import and domestic vehicles.

Don't get caught in the dark again...Light It Up WIth RECON!!!!!

***ATTENTION - VERY IMPORTANT MESSAGE BELOW***

These bulbs are sold individually which means only 1 bulb comes in each package. This means if you need a total of 4 bulbs, you must enter a qty of 4 before clicking the "add to cart" button located below.

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 79643267582

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.3 ★★★★★
Based on 45 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
S
Verified Purchase
Scott Liske
Houston, US
★★★★★ 5
Bright
Color: 7*5in Cube LED Pod
Very bright, good quality
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 12, 2026
R
Verified Purchase
Riik
Dallas, US
★★★★★ 5
Easy to install
Color: 4*2.5in Cube LED Pod
Definitely more than I expected. .. dang good product and easy to install
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 11, 2026
R
Verified Purchase
rkruz
Carnegie, US
★★★★★ 4
Easy Install Onto Jeep JKU, No Switch Backlight or Mounting Holes, Great Customer Service
Color: 5in Cube LED Pod, Color: 5in Cube LED Pod
I installed the Auxbeam 5" 168W LED Cube Pods onto my Jeep JKU Anniversary Steel Bumper. It was an easy install with some YouTube videos to help me snake the cables into the cab. The unused holes in the steel bumper were the perfect size to fit the mounting bolts on the pod lights, and there was plenty of room to reach under the top edge of the bumper to install the nuts with some Loctite. To snake the provided cable through the firewall, I had to remove the installed socket. This was easy to do by simply recessing the retainer clip on each pin, taking a picture of the wired connector before releasing the wires so I knew how to reassemble, snaking the connectorless cable through the firewall into the cab where the pins were then reinserted and locked into the connector. I dressed the cable by zip tie to the existing wire harness at the top of the engine bay. In the cab, I pulled the side panel from the dash (driver's side) and made a small hole for the cable in the panel. After cleaning the dash with alcohol, the adhesive-backed switch seems to hold nicely in place. The lights were very bright and did a great job of illuminating the front and sides of the trail ahead of me. No backlight on the switch, which is a necessity, and I dont understand why that feature is not present. Also, there is no through hole to mount as the adhesive back won't stay attached, so the lack of a mounting hole is a big negative as well. 5 Month UPDATE: One of the lights got water inside. I noticed two screws that hold the glass cover were loose on the bottom of both sides. The other light also had the same loose screws but no water under the glass. I contacted Auxbeam, and they replaced the entire set in 2 days. Very awesome customer service.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 25, 2023
K
Verified Purchase
Kevin Sanguansukdikosol
Waukegan, US
★★★★★ 5
Brightness and quality
Color: 4*2.5in Cube LED Pod
Got this for my 2024 Crosstrek. Got this one specifically due to its functionality that I wanted, quality for the price and it looks great especially DRL. I leave the Amber cover on most of the time. If you want the DRL to be on while the car is on, you can do that but it has to be rewired which I did. Love the brightness. I’ve been having this on my Crosstrek for a few months now and have no issues.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 3, 2026
T
Verified Purchase
Thomas Chapman
Waukegan, US
★★★★★ 5
Bright lights
Color: 4*2.5in Cube LED Pod
Installed these on my Bronco as ditch lights. Very bright light and I like that you can have them be white or put the cover on them for and amber light look. Took about 30 minutes to install and wire to the upfitter switches. They shoot a wide angle covering your blind spots on dark roads. I got these to replace a three inch ditch light. They're made from heavy duty metal and stand up to the extreme weather. I like them so much that I purchased the seven inch lights and install them on the front bumper. For what they cost it was a price that I couldn't pass up. I highly recommend these lights.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 17, 2026

recommand products